Prefielder Cable Technicians
Full-time Employee
North Carolina
Seeking an experienced Prefield Technician to do bonded DSL,running single Line cable troubles etc
Starts
Will need appropriate hand tools to splice cable and do maintenance work.
Pay
30.00 hourly W2. Per Diem is negotiable. Overtime is expected but not guaranteed.
Qualifications
H.S. Diploma. Must have the ability to Pass a Drug Screen and Background Check.
Other Requirements
Will need Valid Driver License/Insurance and Truck, Tools. Must have laptop. Pay Rate is all inclusive of daily expenses.
Job Description
The Copper Cable Splicer must possess the necessary skills, combination of education (minimum 80 hours class room training) and minimum 3 years relevant work experience, tools and test equipment to perform functions including splicing, testing (including pair continuity), count verification, of all types, sizes and gauges of existing and newly constructed PIC and Paper Insulated, color-coded and non-color coded cables. Includes but not limited to:
• Placing and testing pressurized and non-pressurized closures on all types and sizes of cable
• Place, splice and test all types and sizes of load coils, cross connect cabinets, and building entrance protectors
• Placing and testing all types of air pressure devices
• Possess sufficient skill level to effectively place pressure system buffering equipment, when required, to prevent water migration from causing customer outage due to loss of system pressure during splicing operation in pressurized cables.
• Install, test and turn up of all types of subscriber carrier equipment
• Rearranging all outside plant facilities (i.e.: cable throws)
• Pair identification and tagging (tone or battery method)
• Read, comprehend and perform all facets of DSL provisioning
• Sync and Ping of DSL circuits
• Outside Plant facilities provisioning
• Splicing, test and acceptance of digital concentrators
• Splicing, test and acceptance of T-carrier routes for digital concentrators and toll facilities
• Test and acceptance/Test and Tag of special circuits (i.e.: copper cable, digital carrier units, T1’s)
• Read, comprehend, and correct information on cable prints and throw sheets.
• Preparation of all job related work reports (time sheets, corrected cable plans and throw sheets, material sheets.)
MINIMUM TOOLS
• AWL SCRATCH 650
• BIT AUGER TYPE 1/2 X 54IN A542
• BLADE REPL F/D814-66 10056000
• BLOCK/TACKLE W/25FT ROPE 180230S/R
• CLIP HANDLINE SAFETY B CA7710
• CUTTERS BOLT 36IN
• CUTTERS CABLE 36IN 6625
• DRILL 12V CORDLESS 3/8IN REVER
• HAMMER CURVED CLAW 16OZ WOOD H
• HAMMER LINEMANS 36OZ 80936
• HOOK F/MANHOLE COVER 08172
• KNIFE LEAD CABLE SHEATH SPLITTING 1515S
• KNIFE UTILITY 10099
• PLIERS 8-9" LINE
• PLIERS LONG NOSE W/CUTTER 6IN
• PLIERS SIDE CUTTERS B 9IN CA78
• SCISSORS ELEC 5IN W/SERRATED B
• SCREWDRIVER VARIOUS STYLES/SIZES
• SHOVEL FIBERGLASS ROUND LGE
• STAPLER T25
• TENT GROUND CANVAS 62821
• TOOL CRIMP SCOTCHLOK E9BM
• TOOL IMPACT D814 HANDLE
• TOOL WIRE INSERTION MINI MOD MS2 4051
• TOOL WIRE WRAP/UNWRAP 22/24AWG
• WRENCH VARIOUS STYLES/ SIZES
• WRENCH TERMINAL CAN 3/8 X 7/16
• MS2 MODULAR SPLICING RIG W/4036 HAND CRIMPER
• 28’ LADDER (FIBERGLASS OR WOODEN)
• TORQUE WRENCH, INCH POUNDS
• PRE-FORM END PLATE CUTTER
• PRE-FORM BLADE KIT
• CABLE SHAPER
• END PLATE REMOVAL TOOL
• GAUGE, PRESSURE C
• TOOL, PUNCH, BULLET BOND
• Placing and testing pressurized and non-pressurized closures on all types and sizes of cable
• Place, splice and test all types and sizes of load coils, cross connect cabinets, and building entrance protectors
• Placing and testing all types of air pressure devices
• Possess sufficient skill level to effectively place pressure system buffering equipment, when required, to prevent water migration from causing customer outage due to loss of system pressure during splicing operation in pressurized cables.
• Install, test and turn up of all types of subscriber carrier equipment
• Rearranging all outside plant facilities (i.e.: cable throws)
• Pair identification and tagging (tone or battery method)
• Read, comprehend and perform all facets of DSL provisioning
• Sync and Ping of DSL circuits
• Outside Plant facilities provisioning
• Splicing, test and acceptance of digital concentrators
• Splicing, test and acceptance of T-carrier routes for digital concentrators and toll facilities
• Test and acceptance/Test and Tag of special circuits (i.e.: copper cable, digital carrier units, T1’s)
• Read, comprehend, and correct information on cable prints and throw sheets.
• Preparation of all job related work reports (time sheets, corrected cable plans and throw sheets, material sheets.)
MINIMUM TOOLS
• AWL SCRATCH 650
• BIT AUGER TYPE 1/2 X 54IN A542
• BLADE REPL F/D814-66 10056000
• BLOCK/TACKLE W/25FT ROPE 180230S/R
• CLIP HANDLINE SAFETY B CA7710
• CUTTERS BOLT 36IN
• CUTTERS CABLE 36IN 6625
• DRILL 12V CORDLESS 3/8IN REVER
• HAMMER CURVED CLAW 16OZ WOOD H
• HAMMER LINEMANS 36OZ 80936
• HOOK F/MANHOLE COVER 08172
• KNIFE LEAD CABLE SHEATH SPLITTING 1515S
• KNIFE UTILITY 10099
• PLIERS 8-9" LINE
• PLIERS LONG NOSE W/CUTTER 6IN
• PLIERS SIDE CUTTERS B 9IN CA78
• SCISSORS ELEC 5IN W/SERRATED B
• SCREWDRIVER VARIOUS STYLES/SIZES
• SHOVEL FIBERGLASS ROUND LGE
• STAPLER T25
• TENT GROUND CANVAS 62821
• TOOL CRIMP SCOTCHLOK E9BM
• TOOL IMPACT D814 HANDLE
• TOOL WIRE INSERTION MINI MOD MS2 4051
• TOOL WIRE WRAP/UNWRAP 22/24AWG
• WRENCH VARIOUS STYLES/ SIZES
• WRENCH TERMINAL CAN 3/8 X 7/16
• MS2 MODULAR SPLICING RIG W/4036 HAND CRIMPER
• 28’ LADDER (FIBERGLASS OR WOODEN)
• TORQUE WRENCH, INCH POUNDS
• PRE-FORM END PLATE CUTTER
• PRE-FORM BLADE KIT
• CABLE SHAPER
• END PLATE REMOVAL TOOL
• GAUGE, PRESSURE C
• TOOL, PUNCH, BULLET BOND
Contact
x x x x Canceled/Expired Listing x x x x
listed •
expires
job listing #36165 •
tiny link cabl.co/ejzt
