Hydraulic Anchor Cranker/Auger with Power Unit etc
Texas
$4,000.00
Cash / Cashier's check - local pickup(78374), will not deliver.
Description
Atlas Copco - LHPB hydraulic auger with reverse. (Re-hosed in 2018; Valve factory set for 2030psi, ~232 Ft.Lbs. can be adjusted) Sauer-Danfoss OMR-160 Hydraulic Motor
1890 PSI 100% duty cycle (60sec/min - 222 Ft-lbs)
2540 PSI 10% duty cycle (6sec/min - 288 Ft-lbs)
2900 PSI 1% duty cycle (.6sec/min - 339 Ft.-lbs.)
Wisconsin Robin EY27W 8hp engine. Purchased as new old stock. I have approximately 3 hours of work on it running Comp Cams Break-in-oil. It has an additional hour of no-load break-in at idle and 1800rpm.
hp/torque ratings
3600 rpm 7.9 hp - 11.5 ft-lbs
2400 rpm 5.9 hp - 12.9 ft-lbs
1800 rpm 4.4 hp - 12.8 ft-lbs
Dynamic GPF2010PA .61 cu/in hydraulic pump 3600 rpm max - rated 2000 rpm - runs at 50% engine speed 5.6" crank pulley with 2.8" pump pulley
engine 3600 rpm - 4.75 gpm / auger 113 rpm
engine 2400 rpm - 3.17 gpm / auger 75 rpm
engine 1800 rpm - 2.38 gpm / auger 56 rpm
10 Gallon reservoir; Sinopec AW-32; Zinga 10 micron return line filter plumbed at optimal location in relation to pump inlet; Level and temperature gauge.
Mounted on an aluminum cart with wheels.
25 Foot 1/2" hydraulic pressure and return lines with flush-face quick connects.
Lemco - D340 knuckle chuck - for cranking anchors - also fits Stihl BT-360
General Equipment - BT400-6E 6" auger
This unit can put out more torque than the legendary Stihl BT-360 (for reference 3.9hp@8000, geared 151:1 for 50 RPM auger rpm) and has the ability to reverse.
Also comes with spare Atlas Copco LHPB that should be re-hosed before putting into service.
__________________________________________________________
Miscellaneous other small line tools - make fair offer, you pay shipping, or pickup locally
Strand jig
Shotgun - delashing tool
Strand grips
Strand locks
GMP duct projectiles 2" and 4"
1890 PSI 100% duty cycle (60sec/min - 222 Ft-lbs)
2540 PSI 10% duty cycle (6sec/min - 288 Ft-lbs)
2900 PSI 1% duty cycle (.6sec/min - 339 Ft.-lbs.)
Wisconsin Robin EY27W 8hp engine. Purchased as new old stock. I have approximately 3 hours of work on it running Comp Cams Break-in-oil. It has an additional hour of no-load break-in at idle and 1800rpm.
hp/torque ratings
3600 rpm 7.9 hp - 11.5 ft-lbs
2400 rpm 5.9 hp - 12.9 ft-lbs
1800 rpm 4.4 hp - 12.8 ft-lbs
Dynamic GPF2010PA .61 cu/in hydraulic pump 3600 rpm max - rated 2000 rpm - runs at 50% engine speed 5.6" crank pulley with 2.8" pump pulley
engine 3600 rpm - 4.75 gpm / auger 113 rpm
engine 2400 rpm - 3.17 gpm / auger 75 rpm
engine 1800 rpm - 2.38 gpm / auger 56 rpm
10 Gallon reservoir; Sinopec AW-32; Zinga 10 micron return line filter plumbed at optimal location in relation to pump inlet; Level and temperature gauge.
Mounted on an aluminum cart with wheels.
25 Foot 1/2" hydraulic pressure and return lines with flush-face quick connects.
Lemco - D340 knuckle chuck - for cranking anchors - also fits Stihl BT-360
General Equipment - BT400-6E 6" auger
This unit can put out more torque than the legendary Stihl BT-360 (for reference 3.9hp@8000, geared 151:1 for 50 RPM auger rpm) and has the ability to reverse.
Also comes with spare Atlas Copco LHPB that should be re-hosed before putting into service.
__________________________________________________________
Miscellaneous other small line tools - make fair offer, you pay shipping, or pickup locally
Strand jig
Shotgun - delashing tool
Strand grips
Strand locks
GMP duct projectiles 2" and 4"
Contact
x x x x Canceled/Expired Listing x x x x
listed •
expires
classified listing #8253 •
tiny link cabl.co/ccjh